Mi hija quería que le hiciese algo con unas telas que tengo y como tiene una cámara de fotos nueva, se me ocurrió hacerle la funda.
My daughter wanted me to make something for her with some fabrics I
have, and as she has a new camera, I thought it could be a good idea to make a
camera cover.
Necesitamos telas, entretela dura, una cremallera, guata y enganches para el asa.
We need some fabrics,
thick interlining, a zipper, polyester filling and hooks for the handle.
1- Medimos la cámara y cortamos dos rectángulos de la tela exterior y dos de la tela de forro. El ancho de la pieza será la medida de ancho más su grosor y el largo, el alto de la cámara más su grosor. A esto añadiremos un par de centímetros por lo que abulta la guata y para que quede holgada, aparte los márgenes de costura.
De guata, cortamos un rectángulo del mismo ancho que el de las telas y el doble de largo. Y para las asas, una tira de tela 6 cm. x 110 cm., más margen de costura, y una tira de entretela de 3 cm. x 110 cm.
2- Empezamos colocando una pieza exterior y otra del forro, derecho con derecho y con la cremallera en medio, como veis en la foto, y las cosemos.
2- Start by placing an outer piece and a piece of the lining, matching right sides and with the zipper in the middle, as you can see in the photo, sew them.
Repetimos con las otras piezas en la otra parte de la cremallera.
3- A continuación, sin cerrar del todo la cremallera, cosemos las parte exteriores juntas y las del forro juntas también, poniéndolas derecho con derecho y dejando un hueco sin coser en la parte del forro para poder darle la vuelta.
4- Para hacer la base de la funda, colocamos las puntas de las telas como veis en la foto, marcamos una línea perpendicular a la costura a 3 cm. del vértice, cosemos por ella y cortamos dejando un margen de 1 cm.
5- Después, le damos la vuelta y cerramos el hueco a punto escondido.
6- Finalmente, para hacer el asa, planchamos la tira de tela por la mitad y los márgenes de costura hacia dentro, colocamos la entretela dentro y realizamos dos costuras paralelas a los bordes. Por otro lado, cortamos dos pequeños rectángulos, que doblamos y cosemos del mismo modo para luego coserlos a la funda, tras pasarlos por los anillos. Sólo nos queda pasar el asa por los anillos, coser uno de los extremos y enganchar el otro a la pieza corredera.
1- Measure the camera and cut two rectangles of the outer fabric and two
of the lining fabric. The width of the piece must be the measure of width plus
its thickness; and the length must be the height of the camera plus its
thickness. To this, you will add a couple of centimeters because the wadding takes
up space, and to get some extra width, and the seam allowances.
Cut a rectangle of the polyester filling the same width as the fabrics
and twice as long. And for the handles, a strip of fabric 2.4’’ x 43’’, plus
seam allowance, and a strip of interlining of 1.2’’ x 43’’.
2- Empezamos colocando una pieza exterior y otra del forro, derecho con derecho y con la cremallera en medio, como veis en la foto, y las cosemos.
2- Start by placing an outer piece and a piece of the lining, matching right sides and with the zipper in the middle, as you can see in the photo, sew them.
Repeat with
other pieces at the other side of the zipper.
3- Next, without closing completely the zipper, sew the outer sides
together and join also those of the lining, matching right sides and leaving a
gap at lining side to turn the inside out later.
4- To make the base
of the cover, place the edges of the fabrics as you can see in the photo, mark
a perpendicular line to the seam at 1.2’’ from the corner, sew along this line
and cut leaving a margin of 0.4’’.
5- Then turn the inside out and close the gap using hidden stitch.
6- Finally, to make the handle, iron the strip of fabric by half and placing
the seam allowances inside; place the interlining inside and make two seams parallel
to the edges. On the other hand, cut two small rectangles, which you fold and
sew the same way, to sew them to the cover, after pushing them thorugh the
rings. To end, push the handle through for the rings, sew one of the ends and
hook the other one to the sliding piece.
0 comentarios/comments:
Publicar un comentario